In need of parts urgently...

For all technical questions. VIEWABLE without login, you need to register (free) to be able to post a question.
Post Reply
KBUK
Registered User
Posts: 100
Joined: Tue Sep 18, 2018 1:56 pm

Re: In need of parts urgently...

Post by KBUK » Sat Jun 15, 2019 12:49 pm

Pads at front are newish, ebc yellow stuff. Discs were maybe a bit cheap from probestore. They didn't feel perfect since I got the driveshafts changed
Top
KBUK
Registered User
Posts: 100
Joined: Tue Sep 18, 2018 1:56 pm

Re: In need of parts urgently...

Post by KBUK » Sat Jun 15, 2019 4:42 pm

Image

Image

Image

Seems my car went under his. Driver side dipped more than assenger side. Exhaust tip hit the passenger side plastic bumper reinforcement. His bumper hit my radiator cross member. Think if I remove radiator this an be pulled back into place?
Top
KBUK
Registered User
Posts: 100
Joined: Tue Sep 18, 2018 1:56 pm

Re: In need of parts urgently...

Post by KBUK » Sat Jun 15, 2019 4:46 pm

One more part to add to list, coolant reservoir on the right side with the metal cap on top as the hose pipe at the bottom has snapped
Top
cpt black
Tech Rep
Posts: 2824
Joined: Fri Sep 07, 2018 8:28 am
Has thanked: 15 times
Been thanked: 88 times

Re: In need of parts urgently...

Post by cpt black » Sat Jun 15, 2019 5:10 pm

I would say the front cross member is FUBA as it,s bent back and upwards,you would need
a scrap car to cut one out and weld in then a bonnet to align for the bonnet catch and
wing alignment or use bonnet clips to hold down the bonnet, if you go the bonnet clips way
you may get away with pulling the cross member out are the wings scrapping the
doors :?:
Top
KBUK
Registered User
Posts: 100
Joined: Tue Sep 18, 2018 1:56 pm

Re: In need of parts urgently...

Post by KBUK » Sat Jun 15, 2019 5:34 pm

Ok guys, got radiator removed think also need rad for AC and debating to grind out then cross member and replace?
Top
cpt black
Tech Rep
Posts: 2824
Joined: Fri Sep 07, 2018 8:28 am
Has thanked: 15 times
Been thanked: 88 times

Re: In need of parts urgently...

Post by cpt black » Sat Jun 15, 2019 5:47 pm

You may need an A/C Rad if leaking,did my mates one when he hit a deer was,nt leaking so bent
back in shape ;) get a bonnet first and align, bonnet clips or pins will do to hold the bonnet ;)
Top
KBUK
Registered User
Posts: 100
Joined: Tue Sep 18, 2018 1:56 pm

Re: In need of parts urgently...

Post by KBUK » Sat Jun 15, 2019 6:11 pm

cpt black wrote: ↑
Sat Jun 15, 2019 5:10 pm
 I would say the front cross member is FUBA as it,s bent back and upwards,you would need
a scrap car to cut one out and weld in then a bonnet to align for the bonnet catch and
wing alignment or use bonnet clips to hold down the bonnet, if you go the bonnet clips way
you may get away with pulling the cross member out are the wings scrapping the
doors :?:

Wings are absolutely find apart from a tiny bend at the tip near driver light
Top
cpt black
Tech Rep
Posts: 2824
Joined: Fri Sep 07, 2018 8:28 am
Has thanked: 15 times
Been thanked: 88 times

Re: In need of parts urgently...

Post by cpt black » Sat Jun 15, 2019 6:20 pm

Seems you maybe lucky there mate,get a Bonnet and retro fit it to the cross member
and wnigs ;)
Top
Kit
Tech Rep
Posts: 3551
Joined: Fri Sep 07, 2018 8:16 pm
Has thanked: 71 times
Been thanked: 115 times

Re: In need of parts urgently...

Post by Kit » Sat Jun 15, 2019 8:59 pm

With that amount of damage :!:
Didn't the air bags go off !!

There's three crash sensor in the bumper area :?

Kit
Top
KBUK
Registered User
Posts: 100
Joined: Tue Sep 18, 2018 1:56 pm

Re: In need of parts urgently...

Post by KBUK » Sun Jun 16, 2019 1:10 pm

To he honest, it wasn't a bad hit. His car has a very minor scratch on the bumper. We were both braking hard so I think I went underneath and then weight of his sat on the bumper/crossmember
Top
Post Reply

Return to “The Garage - Technical Forum”

Who is online

Users browsing this forum: No registered users and 24 guests