ABS problem

For all technical questions. VIEWABLE without login, you need to register (free) to be able to post a question.
Post Reply
Maria McG
Registered User
Posts: 12
Joined: Tue Mar 30, 2021 9:37 pm
Been thanked: 1 time

ABS problem

Post by Maria McG » Tue Jun 28, 2022 10:09 am

Hi folks,
I'm still working on getting my '97 V6 Probe back on the road.
I need a passenger side rear ABS sensor which doesn't seem to be available in local motor factors.
Any idea where I could get one?
Thanks in advance.
Maria.
Top
Kit
Tech Rep
Posts: 3551
Joined: Fri Sep 07, 2018 8:16 pm
Has thanked: 71 times
Been thanked: 115 times

Re: ABS problem

Post by Kit » Tue Jun 28, 2022 11:36 am

Asked CPT-black to take it off his breaker :!:

Kit
Top
Kit
Tech Rep
Posts: 3551
Joined: Fri Sep 07, 2018 8:16 pm
Has thanked: 71 times
Been thanked: 115 times

Re: ABS problem

Post by Kit » Tue Jun 28, 2022 11:38 am

Try, Rockauto’s, in the ‘State’s’

Kit
Top
jrh
Full Member
Posts: 1022
Joined: Thu Sep 20, 2018 3:08 pm
Been thanked: 43 times

Re: ABS problem

Post by jrh » Tue Jun 28, 2022 1:32 pm

There are only four ways these items can fail.
1/ By the stainless can being crushed by rust.
2/ The can being damaged on removal
3/ The 'sticky-out' peg being damaged by a stone, etc
4/ The cable being damaged
Which one caused yours to fail ?
Top
Micron
Site Admin
Posts: 3334
Joined: Thu Sep 06, 2018 6:08 pm
Has thanked: 61 times
Been thanked: 89 times

Re: ABS problem

Post by Micron » Tue Jun 28, 2022 1:57 pm

Kit wrote: ↑
Tue Jun 28, 2022 11:38 am
 Try, Rockauto’s, in the ‘State’s’

Kit
I had a look, and it appears they don't have any?
Admin and Owner of this fine club 😎
Top
Micron
Site Admin
Posts: 3334
Joined: Thu Sep 06, 2018 6:08 pm
Has thanked: 61 times
Been thanked: 89 times

Re: ABS problem

Post by Micron » Tue Jun 28, 2022 3:13 pm

What are people's thoughts on this, it's for a Mazda MX6 (1997), about £26 delivered? (depending what postage option you go for)

https://www.rockauto.com/en/moreinfo.ph ... 2&jsn=5630
Admin and Owner of this fine club 😎
Top
Kit
Tech Rep
Posts: 3551
Joined: Fri Sep 07, 2018 8:16 pm
Has thanked: 71 times
Been thanked: 115 times

Re: ABS problem

Post by Kit » Tue Jun 28, 2022 7:42 pm

Micron wrote: ↑
Tue Jun 28, 2022 3:13 pm
 What are people's thoughts on this, it's for a Mazda MX6 (1997), about £26 delivered? (depending what postage option you go for)

https://www.rockauto.com/en/moreinfo.ph ... 2&jsn=5630
That’s interesting :?
When you think how hard they can be to remove the stub hub, without damaging them, it’s a bargain

Kit
Top
jrh
Full Member
Posts: 1022
Joined: Thu Sep 20, 2018 3:08 pm
Been thanked: 43 times

Re: ABS problem

Post by jrh » Wed Jun 29, 2022 8:42 am

If all else fails I do have one BUT the cable is only 6 inches long.
It can be spliced onto the existing cable by twisting the wires together NOT SOLDERED.
I can supply all the heat shrinks to make it a good job.
A £3 postage stamp gets it to you.
Top
david_toft
Registered User
Posts: 84
Joined: Tue Sep 11, 2018 5:00 pm
Been thanked: 1 time

Re: ABS problem

Post by david_toft » Wed Jun 29, 2022 10:47 am

What is the problem with soldering the wires together please?
Top
jrh
Full Member
Posts: 1022
Joined: Thu Sep 20, 2018 3:08 pm
Been thanked: 43 times

Re: ABS problem

Post by jrh » Wed Jun 29, 2022 3:13 pm

Because those cables are subject to LOTS of movement and vibration.
It has to be totally flexible.
The wire is much finer than hair , twisting them together is fine , solder and the wire will break on the solder/wire transition.
Top
Post Reply

Return to “The Garage - Technical Forum”

Who is online

Users browsing this forum: No registered users and 33 guests