For all technical questions. VIEWABLE without login, you need to register (free) to be able to post a question.
-
Incognito
- Full Member
- Posts: 2269
- Joined: Thu Sep 06, 2018 9:27 pm
- Has thanked: 48 times
- Been thanked: 18 times
Post
by Incognito » Tue Jun 29, 2021 7:28 pm
jrh wrote: ↑Tue Jun 29, 2021 7:23 pm
Broken spring ?
I'll check John but doesn't seem like that sort of noise , but will run my hand around the spring.
-
Kit
- Tech Rep
- Posts: 3551
- Joined: Fri Sep 07, 2018 8:16 pm
- Has thanked: 71 times
- Been thanked: 115 times
Post
by Kit » Tue Jun 29, 2021 7:30 pm
jrh wrote: ↑Tue Jun 29, 2021 7:23 pm
Broken spring ?
Good call
Once, I changed a spring (strut), he had drove from Paris,
, & didn’t know
Kit
-
Micron
- Site Admin
- Posts: 3335
- Joined: Thu Sep 06, 2018 6:08 pm
- Has thanked: 61 times
- Been thanked: 89 times
Post
by Micron » Tue Jun 29, 2021 7:45 pm
I think I that an overall visual wouldn't go a miss just in case there is anything obvious
Admin and Owner of this fine club
-
Incognito
- Full Member
- Posts: 2269
- Joined: Thu Sep 06, 2018 9:27 pm
- Has thanked: 48 times
- Been thanked: 18 times
Post
by Incognito » Tue Jun 29, 2021 7:59 pm
Micron wrote: ↑Tue Jun 29, 2021 7:45 pm
I think I that an overall visual wouldn't go a miss just in case there is anything obvious
Right ok, Jack up and wheel off over the weekend then, in the meantime I've doused the top strut with WD
-
Kit
- Tech Rep
- Posts: 3551
- Joined: Fri Sep 07, 2018 8:16 pm
- Has thanked: 71 times
- Been thanked: 115 times
Post
by Kit » Tue Jun 29, 2021 8:15 pm
Incognito wrote: ↑Tue Jun 29, 2021 7:59 pm
Micron wrote: ↑Tue Jun 29, 2021 7:45 pm
I think I that an overall visual wouldn't go a miss just in case there is anything obvious
Right ok, Jack up and wheel off over the weekend then, in the meantime I've doused the top strut with WD
With the wheel off, WD40 high up on the u/side of the top Mount as we
Kit
-
fanman
- Full Member
- Posts: 137
- Joined: Fri Sep 14, 2018 10:05 am
- Has thanked: 2 times
- Been thanked: 6 times
Post
by fanman » Wed Jun 30, 2021 3:16 am
For waht it's worth my money is on CV joint. Been there.
-
Incognito
- Full Member
- Posts: 2269
- Joined: Thu Sep 06, 2018 9:27 pm
- Has thanked: 48 times
- Been thanked: 18 times
Post
by Incognito » Thu Jul 01, 2021 6:16 pm
Very little out of work time so far, but did douse the top of the strut with WD. Played about on the road outside just now. Noise still there. Seems to only occur at very low manoeuvring speed turning right , does that throw up anymore clues ? Anti roll pin intact , not had time to check spring. I've a driveshaft in watching ready to buy, not sure on strut top bearing , could I have an ebay link to the correct part please.
-
fanman
- Full Member
- Posts: 137
- Joined: Fri Sep 14, 2018 10:05 am
- Has thanked: 2 times
- Been thanked: 6 times
Post
by fanman » Thu Jul 01, 2021 7:19 pm
Low speed whilst turning is typical of CV joint. Cheapest I can find on Ebay - 203307633209 Says it is for a 16v - not sure if 24v is the same.
-
Kit
- Tech Rep
- Posts: 3551
- Joined: Fri Sep 07, 2018 8:16 pm
- Has thanked: 71 times
- Been thanked: 115 times
Post
by Kit » Thu Jul 01, 2021 9:00 pm
fanman wrote: ↑Thu Jul 01, 2021 7:19 pm
Low speed whilst turning is typical of CV joint. Cheapest I can find on Ebay - 203307633209 Says it is for a 16v - not sure if 24v is the same.
Nop, the 24v is a big size shaft
Kit
Who is online
Users browsing this forum: No registered users and 20 guests
, & didn’t know 