For all technical questions. VIEWABLE without login, you need to register (free) to be able to post a question.
-
Micron
- Site Admin
- Posts: 3318
- Joined: Thu Sep 06, 2018 6:08 pm
- Has thanked: 61 times
- Been thanked: 89 times
Post
by Micron » Tue May 18, 2021 9:21 pm
I checked the codes on the Rio and it came back with code 16 EGR Valve Position
What does that mean in English, what do I need to do to fix it?
Admin and Owner of this fine club
-
Sunfly
- Full Member
- Posts: 1023
- Joined: Fri Sep 07, 2018 9:11 am
- Been thanked: 23 times
Post
by Sunfly » Tue May 18, 2021 11:36 pm
EGR is Exhaust Gas Return or recirculation. The valve returns a metered amount of exhaust gas back to the intake manifold, reducing the oxygen intake which lowers the combustion temp and in so doing reduces the NOx, Nitrous Oxide level and the CO2 levels. It cuts fuel consumption too. There is a sensor that picks up the valve position and tells the ecu all about it. If its genuine, it sounds like a dodgy sensor or connection.
When I had my non starter, I had all kinds of so say faults like that but all were spurious in the end. (CPS damaged wire as it turned out).
-
Micron
- Site Admin
- Posts: 3318
- Joined: Thu Sep 06, 2018 6:08 pm
- Has thanked: 61 times
- Been thanked: 89 times
Post
by Micron » Wed May 19, 2021 8:01 am
Thanks Bob,
Anyone know where it's located, no made rush as I can't do much about it for a few days
Admin and Owner of this fine club
-
humph
- Full Member
- Posts: 31
- Joined: Sat Dec 08, 2018 3:28 pm
- Has thanked: 2 times
- Been thanked: 4 times
Post
by humph » Wed May 19, 2021 8:06 am
The valve and sensor are on the back of the engine on the left side, actually the cylinder head, so at the top.
-
humph
- Full Member
- Posts: 31
- Joined: Sat Dec 08, 2018 3:28 pm
- Has thanked: 2 times
- Been thanked: 4 times
Post
by humph » Wed May 19, 2021 8:10 am
There is also a solenoid involved. Usual problems with them, broken nipple or brittle pipe work. The valve itself can jam up with carbon.
-
Micron
- Site Admin
- Posts: 3318
- Joined: Thu Sep 06, 2018 6:08 pm
- Has thanked: 61 times
- Been thanked: 89 times
Post
by Micron » Wed May 19, 2021 8:13 am
humph wrote: ↑Wed May 19, 2021 8:06 am
The valve and sensor are on the back of the engine on the left side, actually the cylinder head, so at the top.
Hi,
when you say the left side, is that as you look from the front? also are they both bolted to the head and would you have any pictures, although I could look in the parts book!
Admin and Owner of this fine club
-
humph
- Full Member
- Posts: 31
- Joined: Sat Dec 08, 2018 3:28 pm
- Has thanked: 2 times
- Been thanked: 4 times
Post
by humph » Wed May 19, 2021 10:25 am
Right hand side looking from the front, bolted to the rear head. Round, about 3inches across, an electrical connector, a vacuum line and a coolant hose connected to it.
-
Kit
- Tech Rep
- Posts: 3535
- Joined: Fri Sep 07, 2018 8:16 pm
- Has thanked: 70 times
- Been thanked: 115 times
Post
by Kit » Wed May 19, 2021 1:29 pm
In the state, many Probe owners, blank the EGR off
Kit
-
humph
- Full Member
- Posts: 31
- Joined: Sat Dec 08, 2018 3:28 pm
- Has thanked: 2 times
- Been thanked: 4 times
Post
by humph » Wed May 19, 2021 1:32 pm
Kit wrote: ↑Wed May 19, 2021 1:29 pm
In the state, many Probe owners, blank the EGR off
Kit
Mine is for show only, gasket replaced with solid copper gasket. Code 16 is blanked out in my ecu too.
Who is online
Users browsing this forum: No registered users and 26 guests
