Engine hesitating/misfiring slightly when warmed up
Engine hesitating/misfiring slightly when warmed up
Hi my friend has a 2.5litre v6 ford probe registered 1996. For some time the car has hesitated/ slight misfire when warmed up.Ok when cold.Eventually one day it would not start.Got a new distributor, rotor arm, plug leads and plugs ( the correct ones) but car is still stuttering on acceleration .We have tried to get diagnostic leads that will fit but have had no success to date. Can you advise where we can purchase the correct diagnostic leads that will fit this vehicle.Regards Don
-
Micron
- Site Admin
- Posts: 3335
- Joined: Thu Sep 06, 2018 6:08 pm
- Has thanked: 61 times
- Been thanked: 89 times
Re: Engine hesitating/misfiring slightly when warmed up
Hi and welcome to UKPOC,
there is no commercially available tester for these cars as they are OBD1, most cars now are OBD11. Which means the only way to check for codes is with a 12v LED and a wire strap. There is a write up within the oracle, however as you can appreciate, we need to make ends meet, so certain areas of the forum are for full paying members only, but at just £10 per year, it's a bargain really (shameless plug
)
Have you checked the water level at the left hand cap, which is above the inlet manifold, and normally is just a flat cap, rather than a sprung one. the water when cold should be filled to the brim, the method of filling is to remove both caps, but fill from the left hand one, until the water starts to come out of the right hand one, replace that cap then the left hand one.
there is no commercially available tester for these cars as they are OBD1, most cars now are OBD11. Which means the only way to check for codes is with a 12v LED and a wire strap. There is a write up within the oracle, however as you can appreciate, we need to make ends meet, so certain areas of the forum are for full paying members only, but at just £10 per year, it's a bargain really (shameless plug
)Have you checked the water level at the left hand cap, which is above the inlet manifold, and normally is just a flat cap, rather than a sprung one. the water when cold should be filled to the brim, the method of filling is to remove both caps, but fill from the left hand one, until the water starts to come out of the right hand one, replace that cap then the left hand one.
Admin and Owner of this fine club 
Re: Engine hesitating/misfiring slightly when warmed up
I have signed up for membership at £10 per year. How do i access the Probe Oracle to find out more about the above problem.
-
Micron
- Site Admin
- Posts: 3335
- Joined: Thu Sep 06, 2018 6:08 pm
- Has thanked: 61 times
- Been thanked: 89 times
Re: Engine hesitating/misfiring slightly when warmed up
Now that you have full membership, you can look at everything in the oracle.
This is the link you need
http://www.ukpoc.co.uk/forum/viewtopic.php?f=32&t=2713
Admin and Owner of this fine club
Re: Engine hesitating/misfiring slightly when warmed up
Hi again, i have checked the water level and its ok. You state that i need a 12v led and a wire strap. Can a 12v led be easily obtained. Is it just a lamp? Please explain for me. Regards Don
-
Micron
- Site Admin
- Posts: 3335
- Joined: Thu Sep 06, 2018 6:08 pm
- Has thanked: 61 times
- Been thanked: 89 times
Re: Engine hesitating/misfiring slightly when warmed up
Hi Don,
Have you read the write up in the oracle link I posted?
Yes it does need to be a 12v led, because you do not want to load the circuits.
You can buy them from eBay or probably Amazon.
If you follow the write up it will show you if you have any codes.
Admin and Owner of this fine club
Re: Engine hesitating/misfiring slightly when warmed up
Thanks for prompt reply. Yes i have read the article about checking for codes.I will try ebay for 12v led.
Regards Don
Regards Don
Who is online
Users browsing this forum: No registered users and 40 guests