For all technical questions. VIEWABLE without login, you need to register (free) to be able to post a question.
-
el plates
- Full Member
- Posts: 220
- Joined: Thu Sep 06, 2018 9:24 pm
Post
by el plates » Mon Oct 01, 2018 1:15 pm
Think ive asked this before but with the forum issues of late cant find an answer... so here goes.
seen threads on other sites about flywheel skimming and lightweight flywheels, in regards to performance gains.
Is this just a matter of skimming the rear and taking out 25% of the weight?
is this easy to do or does it need to be a strengthened plate?
any guru thoughts out there....???
all the best
-
Micron
- Site Admin
- Posts: 3345
- Joined: Thu Sep 06, 2018 6:08 pm
- Has thanked: 61 times
- Been thanked: 90 times
Post
by Micron » Mon Oct 01, 2018 1:28 pm
If I remember Bob's reply correctly, you have to do a lots of other stuff before you notice any real difference from doing anything with the flywheel, plus I don't think that it's going to make it a performance car!
Admin and Owner of this fine club
-
Jon G 24V
- Tech Rep
- Posts: 659
- Joined: Fri Sep 07, 2018 8:05 pm
- Has thanked: 1 time
- Been thanked: 7 times
Post
by Jon G 24V » Mon Oct 01, 2018 1:44 pm
Thought i heard a few years back that an MX3 Flywheel is lighter than the Probes.
Personally i wouldn't machine an original because if it lets go it will make a mess.
Think you can get Aftermarket ones in the USA.
-
jmx6
- Full Member
- Posts: 367
- Joined: Thu Sep 06, 2018 9:27 pm
- Been thanked: 8 times
Post
by jmx6 » Mon Oct 01, 2018 7:35 pm
I think I have a lightened one in the garage somewhere - I will probably fit it to the replacement engine when I replace the clutch
-
jmx6
- Full Member
- Posts: 367
- Joined: Thu Sep 06, 2018 9:27 pm
- Been thanked: 8 times
Post
by jmx6 » Tue Oct 02, 2018 11:18 pm
Aftermarket - it’s a Fidenza one if I remember correctly
-
Sunfly
- Full Member
- Posts: 1026
- Joined: Fri Sep 07, 2018 9:11 am
- Been thanked: 23 times
Post
by Sunfly » Thu Oct 04, 2018 12:46 am
Lightening the flywheel will make the engine more responsive because it has less weight to accelerate. However it wont give you more power. Power is power and you would need more fuel and air to increase it. The "responsiveness" downside would be that it will decelerate more rapidly too, potentially making gear-changes rough and notchy.
Then there is the balance issue. Remove metal and you run the serious risk of upsetting the balance of the flywheel, either through poor concentricity or through warping as internal stresses in the flywheel are released. Thus you would need to have it re balanced to be on the safe side.
Of course its your flywheel to do with as you will, but my thinking would be that if the designers of one of the worlds biggest engine manufacturers decided that the car would work best with a flywheel of a certain weight, they might well be right!
-
el plates
- Full Member
- Posts: 220
- Joined: Thu Sep 06, 2018 9:24 pm
Post
by el plates » Thu Oct 04, 2018 6:53 am
many thanks, much appreciated....
great informative answer...
will probably leave alone, but was worth the ask as education is always priceless....
all the best
Who is online
Users browsing this forum: No registered users and 35 guests
