For all technical questions. VIEWABLE without login, you need to register (free) to be able to post a question.
-
Andy kay93
- Full Member
- Posts: 239
- Joined: Sun Apr 14, 2019 3:19 pm
Post
by Andy kay93 » Fri Jul 19, 2019 11:15 pm
Hi
Anybody had this? What sort of job is it to repair,
Could inner sills be corroded? What’s best way of checking
Sorry about all questions

Andy
-
el plates
- Full Member
- Posts: 220
- Joined: Thu Sep 06, 2018 9:24 pm
Post
by el plates » Fri Jul 19, 2019 11:31 pm
common issue,
difficult to say, depends on the extent of rust.
any pictures.....
can only check the inners once you have cut out the rust on the outer....
most repairs are doable all depends on how deep your pockets and the overall condition of the rest of the car.
But both inner and out has been replaced before, a lot of work...
all the best

-
cpt black
- Tech Rep
- Posts: 2862
- Joined: Fri Sep 07, 2018 8:28 am
- Location: chatham/kent
- Has thanked: 15 times
- Been thanked: 88 times
Post
by cpt black » Sun Jul 21, 2019 9:11 am
Not too sad wot else did they pull up on the mot

-
Andy kay93
- Full Member
- Posts: 239
- Joined: Sun Apr 14, 2019 3:19 pm
Post
by Andy kay93 » Sun Jul 21, 2019 8:40 pm
Front to rear brake pipes

, now that’s sad

-
Andy W
- Full Member
- Posts: 505
- Joined: Thu Sep 06, 2018 11:49 pm
- Has thanked: 1 time
- Been thanked: 2 times
Post
by Andy W » Sun Jul 21, 2019 9:06 pm
been there. inners are likely to be shot too.
-
Attachments
-

-
Andy kay93
- Full Member
- Posts: 239
- Joined: Sun Apr 14, 2019 3:19 pm
Post
by Andy kay93 » Sun Jul 21, 2019 9:18 pm
Wow! That looks bad, managed to patch mine, ok for
As long as mr Mot is happy, but going forward I would
Replace sills, if only I could get some

-
Andy W
- Full Member
- Posts: 505
- Joined: Thu Sep 06, 2018 11:49 pm
- Has thanked: 1 time
- Been thanked: 2 times
Post
by Andy W » Tue Jul 23, 2019 11:42 pm
Ask Kev (CPT) when he's able to make up a batch next. They aren't a full sill but the rear sections but do fit quite nicely.

-
Andy kay93
- Full Member
- Posts: 239
- Joined: Sun Apr 14, 2019 3:19 pm
Post
by Andy kay93 » Thu Jul 25, 2019 7:49 pm
That’s look great!, what sort of price do you think I’d
Be looking at for both sides?

-
Andy W
- Full Member
- Posts: 505
- Joined: Thu Sep 06, 2018 11:49 pm
- Has thanked: 1 time
- Been thanked: 2 times
Post
by Andy W » Sun Jul 28, 2019 9:57 am
Andy kay93 wrote: ↑Thu Jul 25, 2019 7:49 pm
That’s look great!, what sort of price do you think I’d
Be looking at for both sides?
I think it was around £60 from Kev for inners and outers when I did mine a couple of years ago.
Best ask Kev (CPT black) as it depends if he is still able to make them.
Who is online
Users browsing this forum: No registered users and 32 guests