I have some replacement bushes that I purchased some years ago.Re the bolts I have found the right dimensions on eBay which are 8.8 steel.
Will these be ok
Trailing Arm Bushes
-
Kit
- Tech Rep
- Posts: 3551
- Joined: Fri Sep 07, 2018 8:16 pm
- Has thanked: 71 times
- Been thanked: 115 times
Re: Trailing Arm Bushes
Grade 8.8 steel, is the general grade of steel used in all structural Steelwork fixing, so yes
Kit
Re: Trailing Arm Bushes
Don't forget , the plain, unthreaded length should support the bush sleeve, then cut the threaded excess off later.
You may need to drill the hole in the special washer a shade bigger too.
You may need to drill the hole in the special washer a shade bigger too.
-
david_toft
- Registered User
- Posts: 84
- Joined: Tue Sep 11, 2018 5:00 pm
- Been thanked: 1 time
Re: Trailing Arm Bushes
I measured those long bolts on my car and they are
M12 x 1.25 x 230 long, so metric fine.
My problem is getting them out of the hub where they have rusted in, any suggestions please.
M12 x 1.25 x 230 long, so metric fine.
My problem is getting them out of the hub where they have rusted in, any suggestions please.
Re: Trailing Arm Bushes
Try the easy way first.
Buy the best penetrating oil you can afford , spray into every crack you can see where the bolt goes into the casting holes. Leave for 12 hrs.
Do it all again.
Next day , start hammering . More oil . more hammer.
If it only moves a fraction. Stop, more oil. Hammer it BACK to where it was. More oil.
More hammer, backwards, forwards, etc. etc.
Movement is what you want to see.
Buy the best penetrating oil you can afford , spray into every crack you can see where the bolt goes into the casting holes. Leave for 12 hrs.
Do it all again.
Next day , start hammering . More oil . more hammer.
If it only moves a fraction. Stop, more oil. Hammer it BACK to where it was. More oil.
More hammer, backwards, forwards, etc. etc.
Movement is what you want to see.
-
Jon G 24V
- Tech Rep
- Posts: 659
- Joined: Fri Sep 07, 2018 8:05 pm
- Has thanked: 1 time
- Been thanked: 7 times
Re: Trailing Arm Bushes
I’ve just removed all of the Rear Arms from my MX6.
Yes they were rusty and yes they were a pain but lots of WD40 and working the Bolts backwards and forwards and they should come out OK.
Now the long bolts that go though the Bottom of the Hub for the Lateral Arms, they are a B***h to get out but I still didn’t shear any off,
Yes they were rusty and yes they were a pain but lots of WD40 and working the Bolts backwards and forwards and they should come out OK.
Now the long bolts that go though the Bottom of the Hub for the Lateral Arms, they are a B***h to get out but I still didn’t shear any off,
-
fanman
- Full Member
- Posts: 137
- Joined: Fri Sep 14, 2018 10:05 am
- Has thanked: 2 times
- Been thanked: 6 times
Re: Trailing Arm Bushes
Would these do the trick?
https://www.ebay.co.uk/itm/265192467473 ... SwVgVgwyDK
https://www.ebay.co.uk/itm/265192467473 ... SwVgVgwyDK
Re: Trailing Arm Bushes
NO, NO, NO.
At £43 each they are way over spec.
Ordinary bolts are plenty strong enough to do the job , just look on ebay at ALL the M12 options , there is one there somewhere.
At £43 each they are way over spec.
Ordinary bolts are plenty strong enough to do the job , just look on ebay at ALL the M12 options , there is one there somewhere.
-
fanman
- Full Member
- Posts: 137
- Joined: Fri Sep 14, 2018 10:05 am
- Has thanked: 2 times
- Been thanked: 6 times
Re: Trailing Arm Bushes
I know...but they are so pretty!! 
I guess this is much more practical
:
https://www.ebay.co.uk/itm/264913311129
I guess this is much more practical
:https://www.ebay.co.uk/itm/264913311129
Who is online
Users browsing this forum: Google [Bot] and 30 guests