Clutch

For all technical questions. VIEWABLE without login, you need to register (free) to be able to post a question.
Post Reply
mojo98
Area Rep
Posts: 1087
Joined: Thu Sep 06, 2018 10:52 pm
Has thanked: 3 times
Been thanked: 6 times

Clutch

Post by mojo98 » Mon Jan 20, 2020 5:11 pm

Driving home tonight, dual carriage (outside lane) went to change gear 3 to 4 but unable to change gear :o clutch pedal, near on the floor.
Holly shit where do I go, luckily there was a gap across to the other side of the dual carriage and lucky there was a gap in the other side traffic, so shot across and managed to get off the other side dual carriage, pulled up and car stalled.
Pressed the clutch pedal a few times and it came back up, restarted the car and managed to get a gear, :) so set off for home again (3 miles from home) got home and dumped it until tomorrow.
Where do I start. Answer on a post card please :D

Kit
Tech Rep
Posts: 766
Joined: Fri Sep 07, 2018 8:16 pm
Has thanked: 10 times
Been thanked: 11 times

Re: Clutch

Post by Kit » Mon Jan 20, 2020 5:37 pm

Pinkie, had this :o

The seals in the master clutch cylinder have become weak, & fail to push the fluid,
Check you haven’t got any leaks, either at the slave cylinder or the flexibility pipe under the battery tray, it no leaks it’s more than likely the above.

24v :?: have fun, you may have to take the IM of to get to the master cylinder, :shock:

On the 16v you don’t have to ( done a couple )

Two bolts on master clutch cylinder, one from under the dashboard on the firewall. Taking the drivers seat out, does improve access.

Either, replace master clutch cylinder, for a new one, ( I’m sure you’re have one), or strip it down & replace the rubber seals.

Kit

mojo98
Area Rep
Posts: 1087
Joined: Thu Sep 06, 2018 10:52 pm
Has thanked: 3 times
Been thanked: 6 times

Re: Clutch

Post by mojo98 » Mon Jan 20, 2020 6:32 pm

Cheers Duncan :D :D

jrh
Full Member
Posts: 337
Joined: Thu Sep 20, 2018 3:08 pm
Been thanked: 9 times

Re: Clutch

Post by jrh » Tue Jan 21, 2020 8:17 am

Always a bit concerned that modern practice shares brake and clutch fluid from a common reservoir.
Lucky you could still use the brakes Malcolm.
Let's hope it is a simple job, a bit strange you never had 'gradual' failure though.

Jon G 24V
Tech Rep
Posts: 396
Joined: Fri Sep 07, 2018 8:05 pm
Been thanked: 4 times

Re: Clutch

Post by Jon G 24V » Tue Jan 21, 2020 12:20 pm

I'd look to see if the Flexi Hose is bulging when the Clutch is operated. Might not have gone yet as in split, so no leaks but swelling meaning no Transfer of Fluid Power.

fuerte
Full Member
Posts: 735
Joined: Fri Sep 07, 2018 10:10 am
Has thanked: 18 times
Been thanked: 1 time

Re: Clutch

Post by fuerte » Tue Jan 21, 2020 2:01 pm

Glad you are safe.

mojo98
Area Rep
Posts: 1087
Joined: Thu Sep 06, 2018 10:52 pm
Has thanked: 3 times
Been thanked: 6 times

Re: Clutch

Post by mojo98 » Tue Jan 21, 2020 2:37 pm

Thanks for all the tips, just reading up on how best the change things if needed,
Up to now no leaks but gear changes have been funny for a while now, in fact when the engine is very hot sometimes it very hard to engage 1 gear, and that been like that since 2010, over the years tried several thing (mollyslip) that worked fine. But things have got worse recently, even thought about changing the gear box for a spare, or changing the clutch,
So just have to bite the bullet, and start with the ease job first, bleeding the system and then see what next, this is of course after a good inspection of the pipework 😊

Post Reply

Who is online

Users browsing this forum: No registered users and 5 guests