HT Lead Brackets 24v

For all technical questions. VIEWABLE without login, you need to register (free) to be able to post a question.
fanman
Full Member
Posts: 129
Joined: Fri Sep 14, 2018 10:05 am
Has thanked: 1 time
Been thanked: 6 times

Re: HT Lead Brackets

Post by fanman » Sat May 18, 2019 6:24 pm

fuerte wrote:
Sat May 18, 2019 6:09 pm
fanman wrote:
Sat May 18, 2019 5:53 pm
Twizzle wrote:
Sat May 18, 2019 4:20 pm


Just ordered a roll of red but it'll take 2-3 weeks to come :o
No worries, no rush, - so long as I continue to wake up each morning I am happy to wait!!! :lol:
Just so pleased to be able to get them at last! 8-)
Are you ok.bit concerned about you saying as long as you wake up each morning.
Pm me if you need to talk.
Thanks for your concern......but no, I'm fine thanks ,,, just a standing joke when you get to a certain age !! :lol:

fanman
Full Member
Posts: 129
Joined: Fri Sep 14, 2018 10:05 am
Has thanked: 1 time
Been thanked: 6 times

Re: HT Lead Brackets

Post by fanman » Sat May 18, 2019 6:25 pm

Twizzle wrote:
Sat May 18, 2019 6:10 pm
Actually that’s a very good question, could somebody confirm if the clips are the same please :?
Either way, I will take a set - I will MAKE them work!! :lol:

Twizzle
Registered User
Posts: 111
Joined: Fri Sep 07, 2018 7:58 pm
Has thanked: 4 times
Been thanked: 1 time

Re: HT Lead Brackets

Post by Twizzle » Sat May 18, 2019 6:28 pm

fanman wrote:
Sat May 18, 2019 6:25 pm
Twizzle wrote:
Sat May 18, 2019 6:10 pm
Actually that’s a very good question, could somebody confirm if the clips are the same please :?
Either way, I will take a set - I will MAKE them work!! :lol:
If the 16v ones are different I can make them as long as I have some to work from so it’s not a problem :)

fuerte
Full Member
Posts: 884
Joined: Fri Sep 07, 2018 10:10 am
Has thanked: 22 times
Been thanked: 1 time

Re: HT Lead Brackets

Post by fuerte » Sat May 18, 2019 6:49 pm

fanman wrote:
Sat May 18, 2019 6:24 pm
fuerte wrote:
Sat May 18, 2019 6:09 pm
fanman wrote:
Sat May 18, 2019 5:53 pm


No worries, no rush, - so long as I continue to wake up each morning I am happy to wait!!! :lol:
Just so pleased to be able to get them at last! 8-)
Are you ok.bit concerned about you saying as long as you wake up each morning.
Pm me if you need to talk.
Thanks for your concern......but no, I'm fine thanks ,,, just a standing joke when you get to a certain age !! :lol:
Cool thought it was probably a joke but best to check
Personally would go on the tack as long as I dont wake up in the morning but thats a joke too black sense of humour so dont send the white van for me..

fuerte
Full Member
Posts: 884
Joined: Fri Sep 07, 2018 10:10 am
Has thanked: 22 times
Been thanked: 1 time

Re: HT Lead Brackets

Post by fuerte » Sat May 18, 2019 6:52 pm

Twizzle wrote:
Sat May 18, 2019 6:28 pm
fanman wrote:
Sat May 18, 2019 6:25 pm
Twizzle wrote:
Sat May 18, 2019 6:10 pm
Actually that’s a very good question, could somebody confirm if the clips are the same please :?
Either way, I will take a set - I will MAKE them work!! :lol:
If the 16v ones are different I can make them as long as I have some to work from so it’s not a problem :)
That did occur to me too.I didnt ask.presumably worst case scenario a 16 v wouldnt need as many notches so 24v ones would be ok.look forward to hearing answer for the why me.

Twizzle
Registered User
Posts: 111
Joined: Fri Sep 07, 2018 7:58 pm
Has thanked: 4 times
Been thanked: 1 time

Re: HT Lead Brackets

Post by Twizzle » Fri May 24, 2019 3:36 pm

fanman wrote:
Sat May 18, 2019 6:25 pm
Twizzle wrote:
Sat May 18, 2019 6:10 pm
Actually that’s a very good question, could somebody confirm if the clips are the same please :?
Either way, I will take a set - I will MAKE them work!! :lol:
Red filament arrived today, a week early :), so I can make your set unless you still wish to wait until I find out if there’s any difference between the 16 & 24?

Kit
Tech Rep
Posts: 3404
Joined: Fri Sep 07, 2018 8:16 pm
Has thanked: 65 times
Been thanked: 103 times

Re: HT Lead Brackets 24v

Post by Kit » Fri May 24, 2019 8:49 pm

I’ll find you a 16v lead clip to copy

Its takes four cables :!:

Will bring to Probefest

Kit

Twizzle
Registered User
Posts: 111
Joined: Fri Sep 07, 2018 7:58 pm
Has thanked: 4 times
Been thanked: 1 time

Re: HT Lead Brackets 24v

Post by Twizzle » Fri May 24, 2019 8:56 pm

Kit wrote:
Fri May 24, 2019 8:49 pm
I’ll find you a 16v lead clip to copy

Its takes four cables :!:

Will bring to Probefest

Kit
That’s good of you matey thanks :) is there just the one type as the 24v has three different ones as I’m sure your aware :)

fanman
Full Member
Posts: 129
Joined: Fri Sep 14, 2018 10:05 am
Has thanked: 1 time
Been thanked: 6 times

Re: HT Lead Brackets

Post by fanman » Sat May 25, 2019 1:48 am

Twizzle wrote:
Fri May 24, 2019 3:36 pm
fanman wrote:
Sat May 18, 2019 6:25 pm
Twizzle wrote:
Sat May 18, 2019 6:10 pm
Actually that’s a very good question, could somebody confirm if the clips are the same please :?
Either way, I will take a set - I will MAKE them work!! :lol:
Red filament arrived today, a week early :), so I can make your set unless you still wish to wait until I find out if there’s any difference between the 16 & 24?
Great news! Happy to wait to get correct 16V ones - no rush at all, just happy you are able to help !! :D

Sunfly
Full Member
Posts: 993
Joined: Fri Sep 07, 2018 9:11 am
Been thanked: 21 times

Re: HT Lead Brackets

Post by Sunfly » Sat May 25, 2019 8:35 am

Twizzle wrote:
Mon May 13, 2019 10:52 am
I'm happy to make these if anybody is interested. For those that are familiar with 3D printing they take over 13hrs to print as I make them as a solid unit for strength and not hollow, which is the standard procedure, which in turn means they use quite a lot of filament (material) so not cheap on material or electric. They're printed in ABS which has a melting point of 500F or 260c. At the moment I can make them in Black or Blue, looking to do some in red but need to make an order up for the filament as buying a single roll isn't cheap (£5.00 postage on top of the price for a single roll). I can't do them any cheaper than £10 for a full set to full members only :) If anybody is interested just let me know and I can drop them off at fest :D
Hi Twizzle. You've done a brilliant job of these clips and I would guess they will do their job well where they are located because of the air flow but can I alert you to a potential problem that might be worth checking. If it is ABS you are using, I think you've been quoted the printer injector head temperature rather than the glass transition temperature (when ABS goes floppy) because that starts at about 110deg C. My company vacuum mold a lot of ABS and it goes like pastry from about 110 to 140 deg C.
There are only a few plastics that are capable of retaining their properties above 200c, PTFE being the most common. Its one of the few plastics we can use to make powder coating plugs and shields from, as most plastics transition well below the 210 to 230c curing oven temperature. With safety in mind, can I suggest you put a thermometer in the hottest location for the clips and just check it stays well below 110c.

Post Reply

Who is online

Users browsing this forum: No registered users and 41 guests