Won't start..

For all technical questions. VIEWABLE without login, you need to register (free) to be able to post a question.
KBUK
Registered User
Posts: 100
Joined: Tue Sep 18, 2018 1:56 pm

Re: Won't start..

Post by KBUK » Thu Dec 20, 2018 10:08 am

Just speaking with Adam, recons its the early model.

It's an M-Reg if that helps?

KBUK
Registered User
Posts: 100
Joined: Tue Sep 18, 2018 1:56 pm

Re: Won't start..

Post by KBUK » Thu Dec 20, 2018 10:16 am

cpt black wrote:
Thu Dec 20, 2018 9:58 am
Back to basic,s do you have a key fob :?: to start the car ;) OEM one
Any aftermarket alarms etc added :?:
No aftermarket alarm. Just a key to open the door, twist the ignition and a button to disarm.

cpt black
Tech Rep
Posts: 2663
Joined: Fri Sep 07, 2018 8:28 am
Has thanked: 10 times
Been thanked: 82 times

Re: Won't start..

Post by cpt black » Thu Dec 20, 2018 10:24 am

have you checked the battery in the fob :?: replaced :?:

KBUK
Registered User
Posts: 100
Joined: Tue Sep 18, 2018 1:56 pm

Re: Won't start..

Post by KBUK » Thu Dec 20, 2018 12:17 pm

Plan of attack
1) Sensor arrives tomorrow - Install, pray, start? Failing that...
2) Bypass immobilizer - pray, start? failing that...
3) new alternator - pray, start? failing that...
4) Panic

jrh
Full Member
Posts: 958
Joined: Thu Sep 20, 2018 3:08 pm
Been thanked: 36 times

Re: Won't start..

Post by jrh » Thu Dec 20, 2018 12:31 pm

Stop, stop ,stop.
You have fuel , air, ignition, now, all that is necessary is for it all to happen in the right order and time.
So, it is check the distributor top plug numbers/leads go to the right plug positions on the engine.
Take number one plug out, check that distributor rotor arm is in that position when the piston is at/near top dead centre.
If that happens , put everything back, try starting engine again.
You are sure the petrol is ok ? ?

KBUK
Registered User
Posts: 100
Joined: Tue Sep 18, 2018 1:56 pm

Re: Won't start..

Post by KBUK » Thu Dec 20, 2018 1:13 pm

jrh wrote:
Thu Dec 20, 2018 12:31 pm
Stop, stop ,stop.
You have fuel , air, ignition, now, all that is necessary is for it all to happen in the right order and time.
So, it is check the distributor top plug numbers/leads go to the right plug positions on the engine.
Take number one plug out, check that distributor rotor arm is in that position when the piston is at/near top dead centre.
If that happens , put everything back, try starting engine again.
You are sure the petrol is ok ? ?
- Distributor numbers/leads are all in correct position on the engine
"Take number one plug out, check that distributor rotor arm is in that position"
I can check the plug (remove sparkplug to check where the piston is)
If I remove the HT lead, should I be able to see where the distributor is currently positioned?

Assuming that the cylinder is in the wrong place or the distributor rotor arm is in the wrong place, how do I align them?
Assuming that I can see the cylinder is at the top, the distributor rotor arm is in the right position and it doesn't start, what is next?

cpt black
Tech Rep
Posts: 2663
Joined: Fri Sep 07, 2018 8:28 am
Has thanked: 10 times
Been thanked: 82 times

Re: Won't start..

Post by cpt black » Thu Dec 20, 2018 1:27 pm

long screw driver to check top dead center/ rear plug left hand plug/ remove and use
crankshaft bolt to turn to fully up and rotor arm should point no1 on dissy ,1 repeat till
dissy/no,1 crank should read 10/12 top dead center

KBUK
Registered User
Posts: 100
Joined: Tue Sep 18, 2018 1:56 pm

Re: Won't start..

Post by KBUK » Thu Dec 20, 2018 2:47 pm

cpt black wrote:
Thu Dec 20, 2018 1:27 pm
long screw driver to check top dead center/ rear plug left hand plug/ remove and use
crankshaft bolt to turn to fully up and rotor arm should point no1 on dissy ,1 repeat till
dissy/no,1 crank should read 10/12 top dead center
:?

mikenali
Registered User
Posts: 76
Joined: Mon Oct 22, 2018 12:31 pm
Been thanked: 1 time

Re: Won't start..

Post by mikenali » Thu Dec 20, 2018 5:25 pm

KBUK wrote:
Thu Dec 20, 2018 10:08 am
Just speaking with Adam, recons its the early model.

It's an M-Reg if that helps?
What has caught my attention, is the weak spark on the back bank. Early cars have two crankshaft sensors, one at the end on the crankshaft, and one in the distributor, so having both fail would be unlucky...but not unheard of.

Have you checked the dizzy cap, and rotor arm?

I'd check the timing like cpt black says, then that's one thing off the checklist. The shaking after you let the key go, suggests something isn't quite right with the timing.

Did the RAC bloke check for fault codes?

jrh
Full Member
Posts: 958
Joined: Thu Sep 20, 2018 3:08 pm
Been thanked: 36 times

Re: Won't start..

Post by jrh » Thu Dec 20, 2018 7:35 pm

Good point about 'the shaking'.
That is a serious misfire somewhere.
Are you sure you don't have water getting in via a head gasket leak ?
Check the water level , take both 'rad caps' off and have a look inside the system.

Post Reply

Who is online

Users browsing this forum: No registered users and 45 guests