Nsf noise

For all technical questions. VIEWABLE without login, you need to register (free) to be able to post a question.
Incognito
Full Member
Posts: 2217
Joined: Thu Sep 06, 2018 9:27 pm
Has thanked: 47 times
Been thanked: 18 times

Re: Nsf noise

Post by Incognito » Tue Jun 29, 2021 7:28 pm

jrh wrote:
Tue Jun 29, 2021 7:23 pm
Broken spring ?
I'll check John but doesn't seem like that sort of noise , but will run my hand around the spring.

Kit
Tech Rep
Posts: 3404
Joined: Fri Sep 07, 2018 8:16 pm
Has thanked: 65 times
Been thanked: 103 times

Re: Nsf noise

Post by Kit » Tue Jun 29, 2021 7:30 pm

jrh wrote:
Tue Jun 29, 2021 7:23 pm
Broken spring ?
Good call :idea:

Once, I changed a spring (strut), he had drove from Paris, 🇫🇷, & didn’t know :o

Kit

mojo98
Tech Rep
Posts: 2531
Joined: Thu Sep 06, 2018 10:52 pm
Has thanked: 32 times
Been thanked: 51 times

Re: Nsf noise

Post by mojo98 » Tue Jun 29, 2021 7:37 pm

Check the Drop link

Micron
Site Admin
Posts: 3161
Joined: Thu Sep 06, 2018 6:08 pm
Has thanked: 52 times
Been thanked: 84 times

Re: Nsf noise

Post by Micron » Tue Jun 29, 2021 7:45 pm

I think I that an overall visual wouldn't go a miss just in case there is anything obvious
Admin and Owner of this fine club 😎

Incognito
Full Member
Posts: 2217
Joined: Thu Sep 06, 2018 9:27 pm
Has thanked: 47 times
Been thanked: 18 times

Re: Nsf noise

Post by Incognito » Tue Jun 29, 2021 7:59 pm

Micron wrote:
Tue Jun 29, 2021 7:45 pm
I think I that an overall visual wouldn't go a miss just in case there is anything obvious
Right ok, Jack up and wheel off over the weekend then, in the meantime I've doused the top strut with WD

Kit
Tech Rep
Posts: 3404
Joined: Fri Sep 07, 2018 8:16 pm
Has thanked: 65 times
Been thanked: 103 times

Re: Nsf noise

Post by Kit » Tue Jun 29, 2021 8:15 pm

Incognito wrote:
Tue Jun 29, 2021 7:59 pm
Micron wrote:
Tue Jun 29, 2021 7:45 pm
I think I that an overall visual wouldn't go a miss just in case there is anything obvious
Right ok, Jack up and wheel off over the weekend then, in the meantime I've doused the top strut with WD
With the wheel off, WD40 high up on the u/side of the top Mount as we :idea:

Kit

fanman
Full Member
Posts: 129
Joined: Fri Sep 14, 2018 10:05 am
Has thanked: 1 time
Been thanked: 6 times

Re: Nsf noise

Post by fanman » Wed Jun 30, 2021 3:16 am

For waht it's worth my money is on CV joint. Been there.

Incognito
Full Member
Posts: 2217
Joined: Thu Sep 06, 2018 9:27 pm
Has thanked: 47 times
Been thanked: 18 times

Re: Nsf noise

Post by Incognito » Thu Jul 01, 2021 6:16 pm

Very little out of work time so far, but did douse the top of the strut with WD. Played about on the road outside just now. Noise still there. Seems to only occur at very low manoeuvring speed turning right , does that throw up anymore clues ? Anti roll pin intact , not had time to check spring. I've a driveshaft in watching ready to buy, not sure on strut top bearing , could I have an ebay link to the correct part please. 8-)

fanman
Full Member
Posts: 129
Joined: Fri Sep 14, 2018 10:05 am
Has thanked: 1 time
Been thanked: 6 times

Re: Nsf noise

Post by fanman » Thu Jul 01, 2021 7:19 pm

Low speed whilst turning is typical of CV joint. Cheapest I can find on Ebay - 203307633209 Says it is for a 16v - not sure if 24v is the same. :?:

Kit
Tech Rep
Posts: 3404
Joined: Fri Sep 07, 2018 8:16 pm
Has thanked: 65 times
Been thanked: 103 times

Re: Nsf noise

Post by Kit » Thu Jul 01, 2021 9:00 pm

fanman wrote:
Thu Jul 01, 2021 7:19 pm
Low speed whilst turning is typical of CV joint. Cheapest I can find on Ebay - 203307633209 Says it is for a 16v - not sure if 24v is the same. :?:
Nop, the 24v is a big size shaft

Kit

Post Reply

Who is online

Users browsing this forum: No registered users and 40 guests