Early 24v issues

For all technical questions. VIEWABLE without login, you need to register (free) to be able to post a question.
Post Reply
mojo98
Tech Rep
Posts: 2531
Joined: Thu Sep 06, 2018 10:52 pm
Has thanked: 32 times
Been thanked: 51 times

Early 24v issues

Post by mojo98 » Wed May 19, 2021 12:43 pm

Any idea's, engine starts up with revs at 2000, and when it get up to temp, the revs start hunting. Water levels OK, but water line to iac are cold? Rest are hot
Other issue, timing looks out 14 degs?

Any pointers

Cheer's

Micron
Site Admin
Posts: 3160
Joined: Thu Sep 06, 2018 6:08 pm
Has thanked: 52 times
Been thanked: 84 times

Re: Early 24v issues

Post by Micron » Wed May 19, 2021 2:12 pm

Could it be an air lock, has the water been replaced recently. Do you get warm air out of the heater?
Admin and Owner of this fine club 😎

Sunfly
Full Member
Posts: 993
Joined: Fri Sep 07, 2018 9:11 am
Been thanked: 21 times

Re: Early 24v issues

Post by Sunfly » Wed May 19, 2021 6:14 pm

Micron wrote:
Wed May 19, 2021 2:12 pm
Could it be an air lock, has the water been replaced recently. Do you get warm air out of the heater?
I'd ask the same question as Trev as I had that with my 16v on a couple of occasions.

brookie66J
Full Member
Posts: 43
Joined: Sat Dec 08, 2018 8:05 pm

Re: Early 24v issues

Post by brookie66J » Wed May 19, 2021 11:05 pm

Yes the manifold has been off doing the rocker gaskets , we did try and squeeze the main hoses to see if we could get more air out but they were a bit hot, the heater hoses get hot as well, I'm going to loosen the front hose pipe to the throttle body to see is water comes out.

Sunfly
Full Member
Posts: 993
Joined: Fri Sep 07, 2018 9:11 am
Been thanked: 21 times

Re: Early 24v issues

Post by Sunfly » Wed May 19, 2021 11:12 pm

brookie66J wrote:
Wed May 19, 2021 11:05 pm
Yes the manifold has been off doing the rocker gaskets , we did try and squeeze the main hoses to see if we could get more air out but they were a bit hot, the heater hoses get hot as well, I'm going to loosen the front hose pipe to the throttle body to see is water comes out.
I connected the garden hose to the bottom heater pipe. That fixed it! It went from South Georgia to tropical island paradise.

cpt black
Tech Rep
Posts: 2663
Joined: Fri Sep 07, 2018 8:28 am
Has thanked: 10 times
Been thanked: 82 times

Re: Early 24v issues

Post by cpt black » Thu May 20, 2021 10:30 am

You cold die grind the lugs on the dissy to give more movementand strip
the iac and clean with carb cleaner and by pass the ecr and direct the water pipe
to the iac valve

Jon G 24V
Tech Rep
Posts: 658
Joined: Fri Sep 07, 2018 8:05 pm
Has thanked: 1 time
Been thanked: 6 times

Re: Early 24v issues

Post by Jon G 24V » Fri May 21, 2021 6:36 pm

If the pipes to the IAC are cold then it could be a blockage on the EGR Valve as the IAC water lines run though this.
The EGR has a steel pipe that runs round it and this can corrode and get blocked stopping flow in and out of the IAC.
Also check where the IAC pipe joins the Engine block as this is a steel pipe that can also block up.
You need to get these hot so the IAC is fully open or the Idle will be all over the place 👍

mojo98
Tech Rep
Posts: 2531
Joined: Thu Sep 06, 2018 10:52 pm
Has thanked: 32 times
Been thanked: 51 times

Re: Early 24v issues

Post by mojo98 » Fri May 21, 2021 6:59 pm

Many thanks for everybodies response 👍👍👍

Post Reply

Who is online

Users browsing this forum: No registered users and 26 guests