Engine/gearbox

For all technical questions. VIEWABLE without login, you need to register (free) to be able to post a question.
mojo98
Tech Rep
Posts: 2627
Joined: Thu Sep 06, 2018 10:52 pm
Has thanked: 41 times
Been thanked: 55 times

Re: Engine/gearbox

Post by mojo98 » Thu Oct 29, 2020 4:10 pm

Changed my mind, after giving the gearbox a good clean, I decided to fit it back on the engine,
Not a easy job while working by yourself, but its now refitted to the engine, 😊😊

Will do the rocker cover gaskets tomorrow

mojo98
Tech Rep
Posts: 2627
Joined: Thu Sep 06, 2018 10:52 pm
Has thanked: 41 times
Been thanked: 55 times

Re: Engine/gearbox

Post by mojo98 » Fri Oct 30, 2020 4:11 pm

This is what I use on the gearbox when both drive shafts are removed

X 2

Image

mojo98
Tech Rep
Posts: 2627
Joined: Thu Sep 06, 2018 10:52 pm
Has thanked: 41 times
Been thanked: 55 times

Re: Engine/gearbox

Post by mojo98 » Fri Oct 30, 2020 4:18 pm

Both front and rear rocker cover gaskets changed this afternoon,
Spent a bit more on the rtv sealant (HIGH TEMP SEALANT) see if this works any better, then the normal sealant
Front one didn't really need doing (very slight leak on one corner) but might as well do it while the engine is out.

Micron
Site Admin
Posts: 3335
Joined: Thu Sep 06, 2018 6:08 pm
Has thanked: 61 times
Been thanked: 89 times

Re: Engine/gearbox

Post by Micron » Fri Oct 30, 2020 5:23 pm

mojo98 wrote: ↑
Fri Oct 30, 2020 4:11 pm
This is what I use on the gearbox when both drive shafts are removed

X 2

Image
Is that a machined part?
Admin and Owner of this fine club 😎

cpt black
Tech Rep
Posts: 2823
Joined: Fri Sep 07, 2018 8:28 am
Has thanked: 15 times
Been thanked: 88 times

Re: Engine/gearbox

Post by cpt black » Fri Oct 30, 2020 5:43 pm

Nice handy tool there Malc,got one in plastic to do the trick,seems your getting there
back in tomorrow them mate

mojo98
Tech Rep
Posts: 2627
Joined: Thu Sep 06, 2018 10:52 pm
Has thanked: 41 times
Been thanked: 55 times

Re: Engine/gearbox

Post by mojo98 » Fri Oct 30, 2020 5:58 pm

Micron wrote: ↑
Fri Oct 30, 2020 5:23 pm
mojo98 wrote: ↑
Fri Oct 30, 2020 4:11 pm
This is what I use on the gearbox when both drive shafts are removed

X 2

Image
Is that a machined part?
I believe so, I think Brian O'keefe made them on his lathe, πŸ€”πŸ€”πŸ˜Š

mojo98
Tech Rep
Posts: 2627
Joined: Thu Sep 06, 2018 10:52 pm
Has thanked: 41 times
Been thanked: 55 times

Re: Engine/gearbox

Post by mojo98 » Sun Nov 01, 2020 4:41 pm

Was going to have a day off today, but decided to refit the IM,
Cam covers back on
Power steering belt back on, new alternator brackets/adjuster refitted, but belt left off because the a/c compressor still off will refit later,
Interdiate drive shaft refitted,
Engine finished, but still got loads of work to do, cleaning inside engine bay while the engine is out.
Tidy up the front end,
Got to change a/c condenser.
Rear passenger caliper to change.
Big job putting engine back but no rush, especially with going into lockdown on Thursday
Get up in the loft and get a radiator down, suspect mine had been leaking, front brace was wet when I start to remove the radiator earlier.
😊😊

jrh
Full Member
Posts: 1022
Joined: Thu Sep 20, 2018 3:08 pm
Been thanked: 43 times

Re: Engine/gearbox

Post by jrh » Mon Nov 02, 2020 7:28 am

Another item to check really closely while everything is out.
The power steering 'oil cooler pipe' that runs across the front of the radiator for corrosion.
Replace with copper pipe would be nice.

mojo98
Tech Rep
Posts: 2627
Joined: Thu Sep 06, 2018 10:52 pm
Has thanked: 41 times
Been thanked: 55 times

Re: Engine/gearbox

Post by mojo98 » Mon Nov 02, 2020 8:06 am

jrh wrote: ↑
Mon Nov 02, 2020 7:28 am
Another item to check really closely while everything is out.
The power steering 'oil cooler pipe' that runs across the front of the radiator for corrosion.
Replace with copper pipe would be nice.
Thanks for that info John. Mine looks OK, but will inspect it before I put it back on, plus I have 2 spare's in excellent condition πŸ‘ŒπŸ‘Œ

mojo98
Tech Rep
Posts: 2627
Joined: Thu Sep 06, 2018 10:52 pm
Has thanked: 41 times
Been thanked: 55 times

Re: Engine/gearbox

Post by mojo98 » Wed Nov 25, 2020 12:45 pm

Started putting engine/gearbox back in today,
Put the engine/gearbox in position and dropped the car over the engine/gearbox, couple of engine mount installed, and will setup the engine support this afternoon then then lift the car, and try and get all the other engine mounts in (using Duncan's rear mount) if I don't get them in today will try tomorrow
But still way off getting in running, no rush not going anywhere :D

Post Reply

Who is online

Users browsing this forum: No registered users and 46 guests