Search found 238 matches

by mojo98
Fri Nov 06, 2020 4:03 pm
Forum: The Garage - Technical Forum
Topic: door seals
Replies: 5
Views: 1848

Re: door seals

I would say yes but don't forget there are screws under the rubber top seal,
if I can get up into the loft tomorrow I will take a picture of one that's been removed πŸ‘
by mojo98
Tue Nov 03, 2020 7:03 pm
Forum: The Garage - Technical Forum
Topic: Airbag code 52 repair
Replies: 5
Views: 1367

Re: Airbag code 52 repair

52 -- SRS control module, back-up power supply failure -- wiring, SRS control module

Never seen code 52, will check my books form any diagrams etc,
Dave interested what the electrician to sort out the idle issues
by mojo98
Mon Nov 02, 2020 10:48 am
Forum: The Garage - Technical Forum
Topic: Lime Green 16V in need of some TLC
Replies: 2
Views: 993

Re: Lime Green 16V in need of some TLC

I buy the same battery for 16v as a 24v and I alway buy the AM058L battery

I'm with Trevor need the put load on the battery to check
I do have a ctek battery charger/conditioner, it also let's you know if the battery is u/s, by during charging if the battery won't charge it shows a fault light
by mojo98
Mon Nov 02, 2020 8:06 am
Forum: The Garage - Technical Forum
Topic: Engine/gearbox
Replies: 25
Views: 6711

Re: Engine/gearbox

Another item to check really closely while everything is out. The power steering 'oil cooler pipe' that runs across the front of the radiator for corrosion. Replace with copper pipe would be nice. Thanks for that info John. Mine looks OK, but will inspect it before I put it back on, plus I have 2 s...
by mojo98
Sun Nov 01, 2020 4:41 pm
Forum: The Garage - Technical Forum
Topic: Engine/gearbox
Replies: 25
Views: 6711

Re: Engine/gearbox

Was going to have a day off today, but decided to refit the IM, Cam covers back on Power steering belt back on, new alternator brackets/adjuster refitted, but belt left off because the a/c compressor still off will refit later, Interdiate drive shaft refitted, Engine finished, but still got loads of...
by mojo98
Fri Oct 30, 2020 5:58 pm
Forum: The Garage - Technical Forum
Topic: Engine/gearbox
Replies: 25
Views: 6711

Re: Engine/gearbox

Micron wrote: ↑
Fri Oct 30, 2020 5:23 pm
mojo98 wrote: ↑
Fri Oct 30, 2020 4:11 pm
This is what I use on the gearbox when both drive shafts are removed

X 2

Image
Is that a machined part?
I believe so, I think Brian O'keefe made them on his lathe, πŸ€”πŸ€”πŸ˜Š
by mojo98
Fri Oct 30, 2020 4:18 pm
Forum: The Garage - Technical Forum
Topic: Engine/gearbox
Replies: 25
Views: 6711

Re: Engine/gearbox

Both front and rear rocker cover gaskets changed this afternoon,
Spent a bit more on the rtv sealant (HIGH TEMP SEALANT) see if this works any better, then the normal sealant
Front one didn't really need doing (very slight leak on one corner) but might as well do it while the engine is out.
by mojo98
Fri Oct 30, 2020 4:11 pm
Forum: The Garage - Technical Forum
Topic: Engine/gearbox
Replies: 25
Views: 6711

Re: Engine/gearbox

This is what I use on the gearbox when both drive shafts are removed

X 2

Image
by mojo98
Thu Oct 29, 2020 4:10 pm
Forum: The Garage - Technical Forum
Topic: Engine/gearbox
Replies: 25
Views: 6711

Re: Engine/gearbox

Changed my mind, after giving the gearbox a good clean, I decided to fit it back on the engine,
Not a easy job while working by yourself, but its now refitted to the engine, 😊😊

Will do the rocker cover gaskets tomorrow
by mojo98
Thu Oct 29, 2020 4:04 pm
Forum: The Garage - Technical Forum
Topic: Engine/gearbox
Replies: 25
Views: 6711

Re: Engine/gearbox

jrh wrote: ↑
Thu Oct 29, 2020 2:25 pm
Lovely job Malcolm.
What are you using to stop the drive shaft 'bits' dropping out of line ?
aluminium made stops, πŸ‘ when I remove them I'll post up a picture πŸ‘