Search found 19 matches

by Haulin
Thu May 27, 2021 4:07 pm
Forum: The Garage - Technical Forum
Topic: DOOR KEY LAMP
Replies: 17
Views: 20226

Re: DOOR KEY LAMP

So I did remember wrong.. it's been years since I battled with this same problem. Yeah 6v bulb pops on 12v battery. I tried to diagnose the CPU, but couldn't make any sense of it. But if the ignition key lamp connector has some weird voltage readings, it's 100% faulty CPU. The + pin should have cons...
by Haulin
Mon May 24, 2021 6:28 pm
Forum: The Garage - Technical Forum
Topic: DOOR KEY LAMP
Replies: 17
Views: 20226

Re: DOOR KEY LAMP

Check voltage from the ignition key lamp connector. When my CPU was bad, the ground pin had also some sort of voltage. Also I may remember wrong, but ain't the door key lamps 6 volt ones? Atleast I remember replacing them once with 12v leds, but once I connected the other side, both "died". Disconne...
by Haulin
Wed Jul 08, 2020 7:47 pm
Forum: The Garage - Technical Forum
Topic: 2.0 emissions, CO too high
Replies: 2
Views: 7072

2.0 emissions, CO too high

I've had the 2.0 probe for five years and every single year there's been problems with emissions, HC and CO being too high, this year though only CO, everything else ok. During these years we've changed catalytic converters, lambdas, spark plugs and wires, MAF from 626, "new" 130k km 626 engine as t...
by Haulin
Wed Jun 17, 2020 3:13 pm
Forum: The Garage - Technical Forum
Topic: Fried ECU transistor
Replies: 18
Views: 32532

Re: Fried ECU transistor

ECU arrived and.... She's alive, running smoother than before! :) Thanks Kit for the ECU!
by Haulin
Tue Jun 16, 2020 9:24 am
Forum: The Garage - Technical Forum
Topic: Airbag code 32
Replies: 9
Views: 16335

Re: Airbag code 32

Found the fault with 1 ohm resistor: clock spring :D. Never trust blindly multimeter if it shows continuity. Thanks Sunfly for your help!
by Haulin
Mon Jun 15, 2020 1:44 pm
Forum: The Garage - Technical Forum
Topic: Airbag code 32
Replies: 9
Views: 16335

Re: Airbag code 32

Clock spring indeed still has continuity. Guess I found the safing sensor too (image below), but couldn't get the connectors off, so I just cleaned the dust off on top :evil:. Any idea what size resistor is needed to simulate the airbag? If that wouldn't shut the light, then it has to be something i...
by Haulin
Sun Jun 14, 2020 3:33 pm
Forum: The Garage - Technical Forum
Topic: Airbag code 32
Replies: 9
Views: 16335

Re: Airbag code 32

Thanks again! I'll check the clock spring first with multimeter again to make sure that it indeed works and start looking deeper after that.
by Haulin
Sun Jun 14, 2020 10:41 am
Forum: The Garage - Technical Forum
Topic: Airbag code 32
Replies: 9
Views: 16335

Re: Airbag code 32

Cleaned the two connectors from drivers side (both ends of the clock spring wiring), also waited for the light to go off before starting and still blinks 32. What is safing sensor and where it is located?
by Haulin
Tue Jun 09, 2020 5:39 pm
Forum: The Garage - Technical Forum
Topic: Airbag code 32
Replies: 9
Views: 16335

Re: Airbag code 32

Ah, I see. I'll start with cleaning all the connectors. That waiting procedure would make sense too, I'll test that whenever I get the car running again. Cheers.
by Haulin
Tue Jun 09, 2020 9:46 am
Forum: The Garage - Technical Forum
Topic: Airbag code 32
Replies: 9
Views: 16335

Airbag code 32

Code 32 - drivers airbag, high resistance or open circuit So I've had this code for few years, just randomly going on/off. Sometimes the light blinks immediately after startup, sometimes after driving sometime, sometimes it just goes off when driving and doesn't bother again on that day. Sometimes i...